High quality Cisco ICND1 100-105 dumps pdf training materials and study guides. Update latest Cisco ICND1 100-105 dumps pdf training resources and dumps vce youtube demo. “Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)” is the name of Cisco ICND1 https://www.leads4pass.com/100-105.html exam dumps which covers all the knowledge points of the real Cisco exam. Get the best Cisco ICND1 100-105 dumps exam questions and answers free try download from leads4pass, 100% success and guarantee to pass Cisco 100-105 exam test easily.
Latest Cisco 100-105 dumps pdf questions and answers free download: https://drive.google.com/open?id=0B_7qiYkH83VReEJYRlhNVjdGeVU
Latest Cisco 400-101 dumps pdf questions and answers free download: https://drive.google.com/open?id=0B_7qiYkH83VRQ1BCdmJuZzdZN0U
Vendor: Cisco
Certifications: ICND1
Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)
Exam Code: 100-105
Total Questions: 332 Q&As
QUESTION 1
The command ip route 192.168.100.160 255.255.255.224 192.168.10.2 was issued on a router. No routing protocols or other static routes are configured on the router. Which statement is true about this command?
A. The interface with IP address 192.168.10.2 is on this router.
B. The command sets a gateway of last resort for the router.
C. Packets that are destined for host 192.168.100.160 will be sent to 192.168.10.2.
D. The command creates a static route for all IP traffic with the source address 192.168.100.160.
Correct Answer: C
QUESTION 2
Some routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Correct Answer: BD
QUESTION 3
Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.) 100-105 dumps
Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Correct Answer: CD
QUESTION 4
Which statements are TRUE regarding Internet Protocol version 6 (IPv6) addresses? (Choose three.)
A. An IPv6 address is divided into eight 16-bit groups.
B. A double colon (::) can only be used once in a single IPv6 address.
C. IPv6 addresses are 196 bits in length.
D. Leading zeros cannot be omitted in an IPv6 address.
E. Groups with a value of 0 can be represented with a single 0 in IPv6 address.
Correct Answer: ABE
QUESTION 5
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC
QUESTION 6
Which destination IP address can a host use to send one message to multiple devices across different subnets?
A. 172.20.1.0
B. 127.0.0.1
C. 192.168.0.119
D. 239.255.0.1
Correct Answer: D
QUESTION 7
Which method does a connected trunk port use to tag VLAN traffic?
A. IEEE 802 1w
B. IEEE 802 1D
C. IEEE 802 1Q
D. IEEE 802 1p
Correct Answer: C
QUESTION 8
100-105 dumps Which route source code represents the routing protocol with a default administrative distance of 90 in the routing table?
A. S
B. E
C. D
D. R
E. O
Correct Answer: C
QUESTION 9
ROUTER# show ip route
192.168.12.0/24 is variably subnetted, 9 subnets, 3 masks
C 192.168.12.64 /28 is directly connected, Loopback1
C 192.168.12.32 /28 is directly connected, Ethernet0
C 192.168.12.48 /28 is directly connected, Loopback0
O 192.168.12.236 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0
C 192.168.12.232 /30 is directly connected, Serial0 O 192.168.12.245 /30 [110/782] via 192.168.12.233, 00:35:36, Serial0
O 192.168.12.240 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0
O 192.168.12.253 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0
O 192.168.12.249 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0
O 192.168.12.240/30 [110/128] via 192.168.12.233, 00:35:36, Serial 0
To what does the 128 refer to in the router output above?
A. OSPF cost
B. OSPF priority
C. OSPF hop count
D. OSPF ID number
E. OSPF administrative distance
Correct Answer: A
QUESTION 10
The ip helper-address command does what?
A. assigns an IP address to a host
B. resolves an IP address from a DNS server
C. relays a DHCP request across networks
D. resolves an IP address overlapping issue
Correct Answer: C
QUESTION 11
A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?
A. decrease the window size
B. use a different source port for the session
C. decrease the sequence number
D. obtain a new IP address from the DHCP server
E. start a new session using UDP
Correct Answer: A
QUESTION 12
Why would a network administrator configure port security on a switch?
A. to prevent unauthorized Telnet access to a switch port
B. to prevent unauthorized hosts from accessing the LAN
C. to limit the number of Layer 2 broadcasts on a particular switch port
D. block unauthorized access to the switch management interfaces
Correct Answer: B
Reference: https://www.leads4pass.com/100-105.html dumps exam questions and answers update free try.
Watch the video to learn more: https://youtu.be/trVHfqmuVvgz